Is $12,124 to replace AC and furnace a fair price?
Project Details
My current unit is about 15 years old, and the AC is leaking. I had it filled for the summer but was advised to replace it as it will continue to leak. I use my AC a lot during the summer and want an efficient unit that won't cost a fortune to run. I'm also wondering if I can use my existing Ecobee thermostat instead of the Lennox one included in the quote.
Quote Details
This quote is for the installation of a new Lennox HVAC system, including a furnace, evaporator coil, air conditioner, and smart thermostat. - Furnace: Lennox EL297UH090XV36C - Furnace Specifications: 90,000 BTU, 97% efficiency, 2-stage heat, variable speed ECM motor - Furnace Warranty: 10 year parts, lifetime heat exchanger - Evaporator Coil: Lennox Model # C35-30/36B-2-1 Aluminum Quantum coil - Evaporator Coil Warranty: 10 year parts - Air Conditioner: Lennox Model ML14XC1S-036-230 - Air Conditioner Specifications: 3.0 ton, 14 SEER, R-410A refrigerant - Air Conditioner Warranty: 10 year parts - Thermostat: Lennox iComfort E30 smart thermostat (wifi enabled)
You say...
Vote Distribution
These ratings are not endorsed by Quote Critic. They are submitted by other Quote Critic users like you.
More Details
Category
HVAC
Price
$12,124
Quote Date
October 19, 2025
Home Size
3,000 sq ft
Brand/model
Lennox EL297UH090XV36C (Furnace), Lennox ML14XC1S-036-230 (Air Conditioner)
BTU tonnage
90,000 BTU (Furnace), 3.0 Ton (Air Conditioner)
Efficiency rating
97% AFUE (Furnace), 14 SEER (Air Conditioner)
Parts warranty
10
System type
Furnace, Air conditioner
Comments
No comments yet
Sign in to share your thoughts and ask questions.
Similar Quotes
Perform comprehensive HVAC system repair and maintenance
This quote covers a comprehensive set of HVAC services, including: - Uninstallation and disposal of the old damaged coil. - Leak free installation of the new coil. - Full system testing and calibration for peak performance. - Uninstallation and disposal of the old damaged filter drier. - Leak free installation of the new filter drier. - Full system testing and calibration for peak performance. - Refrigerant leak detection. - Recover refrigerant. - Nitrogen purge. - Leak repair. - Pressure test. - All refrigerant recovery and recycling following EPA protocol. - Purging refrigerant lines with dry nitrogen. - Accurate refrigerant weigh in/out with calibrated scale. - Complete refrigerant testing for peak system operation using super heat and sub cooling diagnostics. - Adding refrigerant to EPA guidelines. - Remove schrader core with isolation tool. - Install new schrader core and new cap. - Leak test service valve.
Install Mitsubishi 9KBTU Hyperheat Mini Split Heat Pump System for one room
- Perform manual J Load calculation to understand true heating and cooling loads for the area of house served by the furnace - Furnish and install new Heatpump system consisting of Outdoor Unit and Wall Mounted Indoor Unit - Furnish and install Refrigerant piping, interlock wiring and drain tubing - Furnish and install Linehide to cover refrigerant , drain and wire - Furnish and install Condenser Pad - Start up and check test of operation - 1 year labor warranty - 12 year limited manufacturer’s parts warranty
Install a new furnace and heat pump
This quote is for the full replacement of an existing furnace and A/C unit, including the relocation of the A/C unit. - Furnace: Lennox Elite EL297UHV - Furnace BTU: 66,000 Btu - Furnace Stages: 2 stage variable gas - Furnace Efficiency: 97% - AC Unit: Kinghome Ultranixx KD24 - AC Tonnage: 2 ton - AC Type: Side discharge central air - AC Speed: Variable speed - AC Efficiency (SEER2): 15.2 - AC Sound Rating: As low as 56 dB - Included Items: 2 Surge protectors (complimentary) - Installation Work: Replace copper line set and outdoor disconnect box - Installation Work: Install a new equipment pad below the outdoor unit - Installation Work: Connect with the existing ductwork, gas supply, electrical, and 636 venting - Installation Work: Install a new 636 PVC furnace vent pipe system out the west wall, near the front corner - Installation Work: Remove the existing humidifier and install patch plates on the ductwork - Installation Work: Dispose of the old equipment - Installation Work: Move the A/C unit from the back of the house to the side of the house